# LP Pump Power Shutdown **URL:** \ **Category:** Help & Support\ **Created:** [September 20, 2024, 12:44am UTC](https://community.wazer.com/t/lp-pump-power-shutdown/1083 "2024-09-20T00:44:28Z")\ **Posts on this page:** 6\ **Page:** 1
**Author:** ![DuckieDee](https://avatars.discourse-cdn.com/v4/letter/d/b38774/32.png) [@DuckieDee](https://community.wazer.com/u/DuckieDee)\ **Post date:** [September 20, 2024, 12:44am UTC](https://community.wazer.com/t/lp-pump-power-shutdown/1083/1 "2024-09-20T00:44:28Z")
Last week i was running a job that was cutting for about 3 hours then the wazer auto powered down and restarted. From there, it will not run at all. Checked multiple issues. Water levels - tried high and low. firmware was on 2.30, now 2.32 (sorry, had to add each photo seperate as is does not “allow” new users to post more than 1 photo at a time) Every time we try to do a check on the LP Lump, it shuts off the power. The images attached are where the levels are now when it shuts off and does the same when’s it’s higher. If I attempt to do a tank cleaning, the power will shut off as well or the start button does not come on to start. Neither does a cancel button. I am only near this machine for this job every Friday and of course it’s when the support desk is closed and having constant issues is a huge issue. ![IMG_7384](https://canada1.discourse-cdn.com/flex027/uploads/wazer/original/1X/423147b41a68588f6896f627131e1c8162adbb7f.jpeg) ---
**Author:** ![DuckieDee](https://avatars.discourse-cdn.com/v4/letter/d/b38774/32.png) [@DuckieDee](https://community.wazer.com/u/DuckieDee)\ **Post date:** [September 20, 2024, 12:51am UTC](https://community.wazer.com/t/lp-pump-power-shutdown/1083/2 "2024-09-20T00:51:27Z")
![IMG_7385](https://canada1.discourse-cdn.com/flex027/uploads/wazer/original/1X/871905c09361a7181f3f24ba17c76b7ca0340019.jpeg) ---
**Author:** ![DuckieDee](https://avatars.discourse-cdn.com/v4/letter/d/b38774/32.png) [@DuckieDee](https://community.wazer.com/u/DuckieDee)\ **Post date:** [September 20, 2024, 12:52am UTC](https://community.wazer.com/t/lp-pump-power-shutdown/1083/3 "2024-09-20T00:52:07Z")
![IMG_7386](https://canada1.discourse-cdn.com/flex027/uploads/wazer/original/1X/5da5b07dff1a1e630afd26e0d2dc757a30880220.jpeg) ---
**Author:** ![DuckieDee](https://avatars.discourse-cdn.com/v4/letter/d/b38774/32.png) [@DuckieDee](https://community.wazer.com/u/DuckieDee)\ **Post date:** [September 20, 2024, 1:20am UTC](https://community.wazer.com/t/lp-pump-power-shutdown/1083/4 "2024-09-20T01:20:29Z")
![thumbnail_IMG_7391](https://canada1.discourse-cdn.com/flex027/uploads/wazer/original/1X/d51399a96cb9002bbdbeeabbdba1a8b79e2d2eae.jpeg) this photo is from when i did a water sensor level test and when i hand lift that sensor, the machine does not turn off though it will if i do the very top one. HOWEVER, when i did the waster sensor test once this prong hit straight the machine rebooted. ---
**Author:** ![DuckieDee](https://avatars.discourse-cdn.com/v4/letter/d/b38774/32.png) [@DuckieDee](https://community.wazer.com/u/DuckieDee)\ **Post date:** [September 20, 2024, 1:37am UTC](https://community.wazer.com/t/lp-pump-power-shutdown/1083/5 "2024-09-20T01:37:50Z")
also, its i “try” to run a job just for the heck of it - i get this message when everything is cleared ![IMG_7392](https://canada1.discourse-cdn.com/flex027/uploads/wazer/original/1X/e55778edf8218a20a5eb7c4d77868888978d5049.jpeg) ---
**Author:** ![Wazer203](https://avatars.discourse-cdn.com/v4/letter/w/e19b73/32.png) [@Wazer203](https://community.wazer.com/u/Wazer203)\ **Post date:** [October 29, 2025, 9:49pm UTC](https://community.wazer.com/t/lp-pump-power-shutdown/1083/6 "2025-10-29T21:49:37Z")
October 2025. Was there a solution to this? I have the same situation. Thanks!